Wednesday, May 23, 2018

IAM Search

DC Electrical resistance and Ohm’s Law

Third Part of DC Electricity for Industrial Instrumentation

To review, voltage is the measure of potential energy available to electric charges. Current is the uniform drifting of electric charges in response to a voltage. We can have a voltage without having a current, but we cannot have a current without first having a voltage to motivate it1. Current without voltage would be equivalent to motion without a motivating force.

When electric charges move through a material such as metal, they will naturally encounter some friction, just as fluid moving through a pipe will inevitably encounter friction2. We have a name for this friction to electrical charge motion: resistance. Like voltage and current, resistance has its own special unit of measurement: the ohm, named in honor of the German physicist Georg Simon Ohm.

At this point it would be good to summarize and compare the symbols and units we use for voltage, current, and resistance:


Algebraic symbol
Unit abbreviation
Voltage V (or E) Volt V
Current I Ampere (or Amp) A
Resistance R Ohm Ω


Ohm defined resistance as the mathematical ratio between applied voltage and resulting current:

R =V / I

Verbally expressed, resistance is how much voltage it takes to force a certain rate of current through a conductive material. Many materials have relatively stable resistances, while others do not. Devices called resistors are sold which are manufactured to possess a very precise amount of resistance, for the purpose of limiting current in circuits (among other things).

Here is an example of Ohm’s Law in action: calculate the amount of current in a circuit with a voltage source of 25 V and a total resistance of 3500Ω . Taking 25 volts and dividing by 3500 ohms, you should arrive at a result of 0.007143 amperes, or 7.143 milliamperes (7.143 mA).

One of the most challenging aspect of Ohm’s Law is remembering to keep all variables in context. This is a common problem for many students when studying physics as well: none of the equations learned in a physics class will yield the correct results unless all the variables relate to the same object or situation. For instance, it would make no sense to try to calculate the kinetic energy of a moving object (E = 1 2mv2) by taking the mass of one object (m) and multiplying it by the square of the velocity of some other object (v2). Likewise, with Ohm’s Law, we must make sure the voltage, current, and resistance values we are using all relate to the same portion of the same circuit.

1Except in the noteworthy case of superconductivity, a phenomenon occurring at extremely low temperatures.

2Except in the noteworthy case of superfluidity, another phenomenon occurring at extremely low temperatures.

If the circuit in question has only one source of voltage, one resistance, and one path for current, there cannot be any mix-ups. Expressing the previous example in a schematic diagram:


However, if we look at a more complex circuit, we encounter the potential for mix-ups:




Which resistance do we use to calculate current in this circuit? Do we divide our 25 volts by 3500 ohms like we did last time, or do we divide it by 1500 ohms, or something entirely different? The answer to this question lies in the identification of voltages and currents. We know that the 25 volt potential will be impressed across the total of the two resistances R1 and R2, and since there is only one path for current they must share the same current. Thus, we actually have three voltages (V1, V2, and Vtotal), three resistances (R1, R2, and Rtotal), and only one current (I):



Manipulating the Ohm’s Law equation originally given (R = V I ) to solve for V , we end up with three equations for this circuit:

Vtotal = IRtotal = I(R1 + R2)

V1 = IR1

V2 = IR2

Thus, the current in this circuit is 5 milliamps (5 mA), the voltage across resistor R1 is 17.5 volts, and the voltage across resistor R2 is 7.5 volts.


Click here to go to the contents page of Basic DC Electricity for Indusrtial Instrumentation

Click here to go back reading on the DC Electrical Current - Second Part of DC electricity for Industrial Instrumentation.

Click here to continue reading on the DC Series Versus Parallel Circuits - Fourth Part of DC electricity for Industrial Instrumentation

Go Back to Lessons in Instrumentation Table of Contents

Comments (0)Add Comment

Write comment

security code
Write the displayed characters



  • ...more


Important: All images are copyrighted to their respective owners. All content cited is derived from their respective sources.

Contact us for information and your inquiries. IAMechatronics is open to link exchanges.

IAMechatronics Login